Please look for it we!
Related guide: 5GHz WiFi Antenna
5GHz MIMO Sector Antenna for 360-Degree Coverage - RF element
5GHz MIMO Sector Antenna for 360-Degree Coverage - RF element

5GHz MIMO Sector Antenna for 360-Degree Coverage

  • Frequency Range: 5150-5850 MHz
  • Gain: >15 dBi (optimized for maximum signal strength)
  • Beamwidth: 90 degrees (horizontal), ensuring uniform coverage in a sector
  • Polarization: ±45 degrees for reduced interference in multi-antenna setups

Specifications

This 5GHz MIMO sector antenna delivers more than 15dBi across 5150-5850MHz with a 90 degree horizontal beam and dual-slant polarization, and it is designed to be used in sets of four to build a full 360 degree coverage ring. Each unit mounts on a single pole, so a point-to-multipoint 5.8GHz access site can be assembled from four identical sectors instead of a mix of omni and sector hardware.

Four sectors, one ring

An omnidirectional antenna spreads its energy around a full circle, which is convenient but wasteful when the subscribers are clustered in specific directions, as they almost always are at a WISP access site. Four 90 degree sectors put the same transmit power into a quarter of the circle each, raising gain in every direction and letting each sector carry its own radio channel. The result is both more range and more capacity from the same mast.

Sectorization also localizes interference. When a subscriber in one direction reports a problem, the operator can see which sector and which channel is involved instead of troubleshooting an undifferentiated 360 degree cell.

Why 15dBi and 90 degrees

The 90 degree horizontal beamwidth is what makes four units tile a full circle with modest overlap. Narrow the beam and the ring needs more sectors; widen it and the sectors overlap so heavily that the extra gain disappears into wasted coverage. Fifteen dBi is the gain that a compact sector of this width can hold across 5150-5850MHz without growing into a panel that is difficult to mount on a pole.

We achieved the target by reworking the aluminum reflector to produce a more focused forward pattern rather than by lengthening the antenna. The ±45 degree dual-slant elements then give each sector two decorrelated polarizations, which is what the MIMO radio needs and what keeps co-located sectors from interfering with each other as much as a single-polarized design would.

Specifications

ParameterValue
Frequency range5150-5850MHz
Gain>15dBi
VSWR<1.8
Polarization±45° dual-slant
Horizontal beamwidth90°
MountingPole mount
Typical configuration4 units for 360° coverage

Site planning

Mount the four sectors at the same height with their boresights at 0, 90, 180 and 270 degrees, and set mechanical downtilt from the coverage radius rather than from a default. Keep a small deliberate overlap at the sector edges so that a subscriber crossing a boundary is handed over rather than dropped. Where the pole also carries other equipment, separate the sectors vertically from any broadband antenna to avoid pattern distortion in the horizontal plane.

Use equal-length jumpers on all four sectors and keep the radio as close to the antennas as practical. At 5.8GHz, a long feeder run can consume more signal than the sector gain provides, and the effect is worse on the sector with the longest cable, which shows up as an unbalanced ring that is easy to blame on the antenna.

Customization and ordering

Beamwidth, gain, polarization and connector type can be adjusted, and a version with a different horizontal pattern is available where the site uses three sectors instead of four. Mounting brackets can be matched to an existing pole diameter, and radome colour and OEM labelling are open to change.

Send the coverage plan, sector count, band and connector type to sales@rfelement.com. Samples are typically ready in 3-5 working days and mass production in 15-25 working days.

FAQ — 5GHz MIMO Sector Antenna for 360-Degree Coverage

What is the 5GHz MIMO Sector Antenna for 360-Degree Coverage used for?

The 5GHz MIMO Sector Antenna for 360-Degree Coverage is a custom RF antenna built for telecom, IoT and wireless infrastructure. It is engineered for stable signal coverage and is available in both indoor and weatherproof outdoor (IP-rated) variants.

What frequency band does the 5GHz MIMO Sector Antenna for 360-Degree Coverage cover?

The 5GHz MIMO Sector Antenna for 360-Degree Coverage is specified for 5150-5850MHz. If your project uses an adjacent or custom band, send the target frequency plan and we will confirm feasibility on the same mechanical platform.

What are the key specifications of the 5GHz MIMO Sector Antenna for 360-Degree Coverage?

Key specifications of the 5GHz MIMO Sector Antenna for 360-Degree Coverage: frequency range 5150-5850MHz, gain >15dBi, polarization ±45° dual-slant, VSWR <1.8. The full electrical and mechanical table is listed above, and custom values are available on request.

Can RF element customize the 5GHz MIMO Sector Antenna for 360-Degree Coverage for my application?

Yes. RF element manufactures the 5GHz MIMO Sector Antenna for 360-Degree Coverage in house and supports OEM/ODM. Connector type, cable length, mounting hardware, radome colour and mechanical dimensions can all be changed, and gain or beamwidth can be retuned for your coverage plan.

What is the MOQ and lead time for the 5GHz MIMO Sector Antenna for 360-Degree Coverage?

RF element supports low MOQ to help customers scale from prototype to mass production. Typical lead time is 3-5 working days for samples and 15-25 working days for mass production. Contact sales@rfelement.com for a quotation.

How do I get a quotation for the 5GHz MIMO Sector Antenna for 360-Degree Coverage?

Send your requirements (frequency band, gain, quantity, application) to sales@rfelement.com or use the Contact Us page. Our engineering team responds within 1-2 hours during working hours.
Let's Talk
We can help you figure out your needs.
Contact UsArrow
Contact UsArrow
Content last updated: November 2026 · Reviewed by RF element Engineering Dept.
Contact RF element